subscription ran out

Tue Jul 28 2015, 15:37 by juliecg

hi all thanks for the add
does anybody know how I could update my starview 7 box as my …

Comments: 0

greetings

Mon Jul 13 2015, 05:27 by guffie999

just a few words thanking the people [ & mods ]  on this forum for accepting my application to …

Comments: 4

sly f5 boxes

Sun Apr 26 2015, 22:06 by renault786

hello everyone new to all this, anyone know about slyf5 box

Comments: 1

Affiliates
Get a free Giffgaff Sim ... MrModchips Newsdemon

starview combo

View previous topic View next topic Go down

starview combo

Post by thedon11 on Fri Sep 23 2011, 23:53

hi guys,got a starview combo,power it up and all i get is a green dot on the display,cant get into the engineers menu,cant even put into standby mode,i can olny power it up by the switch on the back,my tv is not even picking the scart up,any ideas please

thedon11
Learning
Learning

Number of posts : 32
Registration date : 2011-02-12

Back to top Go down

Re: starview combo

Post by dooby2oon on Sat Sep 24 2011, 08:41

You need to run the mac fix software this should sort it out files in downloads



THIS IS FOR THE STARVIEW HD COMBO +

IF YOURS DOES NOT HAVE A LAN PORT DO NOT USE THIS FIX!!!!!

You will need:
A computer with a serial port
A Null modem 9 pin serial cable (as used on the starview 1 - 3)
Connect the SV HD to the computer using the serial cable and attach to mains (leave turned off by switch on back)
UNZIP the file downloaded
open HD-200_Download.exe
Choose COM 1 (unless you have connected it to a different port)
Select software (HD300N_SC_RS232_1.bin)
Turn on receiver with rear switch
bar will start counting to 100%
WAIT UNTIL SOFTWARE SAYS COMPLETE!!!!
Turn off receiver and back on
P.S. This will also recover 'bricked' SVHD's (if there are any lights still on)
Once complete the receiver will be as factory provided.
If your Starview HD has lost its MAC address this is what you need to do next:
Go to accessory - network - ip config
Set IP to manual
You can now edit the MAC address back to the original receivers address - Your mac address is on a sticker inside the receiver (you can see it through the vents on the top)
apply then exit.
Then you can start from scratch loading which ever firmware you choose.

.

Doobz
avatar
dooby2oon
.
.

Male
Number of posts : 578
Age : 44
Location : Inside You
Registration date : 2008-08-11

http://www.freewebs.com/dooby2oon/

Back to top Go down

Re: starview combo

Post by thedon11 on Sat Sep 24 2011, 12:36

thanks buddy i'l give it a go when i get in cheers again

thedon11
Learning
Learning

Number of posts : 32
Registration date : 2011-02-12

Back to top Go down

Re: starview combo

Post by thedon11 on Sat Sep 24 2011, 13:40

no luck dooby2oon selected com port via null cable connected,choosen the file,turn sv box on,and nothing happens the percentage bar does not move,seems like nothing is being loaded,need help plz

thedon11
Learning
Learning

Number of posts : 32
Registration date : 2011-02-12

Back to top Go down

Re: starview combo

Post by dooby2oon on Sun Sep 25 2011, 10:46

Have you set your com port in windows to com 1 to 4
read the first section in link below on how to change and set com port in windows, if you have a valid com port set try a diff one then try again

also when in windows ports setting make sure bits per second is set to 115200 and flow control set at none

http://www.freewebs.com/starview-update/

.

Doobz
avatar
dooby2oon
.
.

Male
Number of posts : 578
Age : 44
Location : Inside You
Registration date : 2008-08-11

http://www.freewebs.com/dooby2oon/

Back to top Go down

Re: starview combo

Post by Sponsored content


Sponsored content


Back to top Go down

View previous topic View next topic Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum